#TENPOINT CROSSBOW STRING WAX FREE#

The process requires some bit of training mostly on a practical basis. Stringing a crossbow is not just an ordinary task especially if you have little information about them. The most recommended number of shots to take before restringing a crossbow is between00-500 shots. If you want to do it yourself and need to know hot to string a crossbow yourself, it can be done but care must be taken to do it safely. The easiest way to change out an old xbow string is to take the weapon to an authorized dealer. It’s loud, scary, and can be extremely dangerous, often times shattering the limbs and sending pieces everywhere.Īlways examine the string for wear and tear! Snapping an xbow string is not a fun experience. If you are shooting an xbow with a frayed string or an old string that has not been changed for quite some time you are asking for trouble.

Driving around on bare tires with poor quality treads is dumb and dangerous. Treat the string on your crossbow like tires on your vehicle. If you see the string on your xbow showing signs of fraying or becoming fuzzy around the outer edges do not hesitate to get the string replaced. proof wax.Īnother common mistake people do is to use oil-based lubricants on the rail which soak into the string and cause it to decay and weaken over time. rays will damage the fibers in the string quickly if not coated in U.V. Xbow strings will last a lot longer when waxed frequently and the weapon is stored properly and out of the sun. The last thing you want is to have string issues while out hunting! As one of the most important parts of an xbow, the string needs to be especially well maintained and cared for. This method is however less popular since few crossbows come with prey.Ĭrossbow String Replacement Can Be DangerousĬrossbow strings are under a tremendous amount of force and pressure during regular every day use. Do not forget to wax the end of the bowstring to increase grid.ĭIY works on the same principle with a stringer cable in that it comes with prey that helps you in adjusting and tightening the limbs to remove and replace the bowstring. Unhook the other end of the stringer, and there you have your crossbow ready. Release the tension by firing the crossbow, and one end of the stringer will fall leaving the string holding the tension.

#TENPOINT CROSSBOW STRING WAX FREE#

Once done, cock the bow and attach the other free end of the string on the remaining nock.

Many crossbow models from big brands like Ten Point, Horton, Mission and Barnett ship with cable stringers. To be started, attach the string onto the nock and later attach all ends of the cable stringer on both nocks of the crossbow. A stringer works as a lightweight string.

This process is simpler than using the bow press. Restring using a cable stringer A stringer can be used to string a crossbow during replacement. Once you replace, wax your string at both ends to increase tightness and have a test if your crossbow and the string is well tight. When you press the limbs, the string becomes loose so you can remove them and replace.Ĥ). Hook your crossbow on either side with the bow press and adjust the bow press button that sees the bow becoming tight while at the same time pulling the limbs together. Once done inspecting, place your crossbow and the bow press on a flat surface. Do not trust the manufacturer too much.ģ). Also, there is a need to examine the string for any fault from the manufacturer. Examine the old string and be quite careful because, in case of any breakages, the string may snap in the middle of the process and cause injuries. to start, you will need to have your bow press-ready, new bowstring that is certified, bowstring wax and perhaps eye protection devices.Ģ). Ensure you are using a bow press certified by crossbow manufactures. Restringing Crossbows using Bow PressĪs we have said, a Bow press is only used to restring Reverse compound and the compound crossbows. Bow press acts to compress the limbs so that the string can get relaxed to ease removal and replacement of string. To restring Recurve crossbow, you can use your bare hands, and a special type of cable called the stringer but for the Compound, and the Reverse Compound, you will undoubtedly need to have a bow press. In the real sense, we have three types of crossbows namely Compound, Reverse compound and the Recurve Crossbow. Though lubricating the rail of a crossbow or waxing the string can help reduce the wearing process, the need to restring crossbow after prolonged use is very vital. In any item that is on frequent use, wear and tear are never avoidable. Some strings can be changed using your hands, others require a bow press or string changing cable for crossbow string replacement.

Changing a crossbow string requires different tools.

Tenpoint crossbow string wax